Practice Problem Analysis and Presentation Guidelines
Purpose
The purpose of this assignment is to critically evaluate a practice problem. This assignment builds on the Week 4 assignment: Translation Science Project. Information used in the Week 4 assignment may be used as the basis for this assignment. The goal of the assignment is to develop a deeper understanding of the practice issue, using continuous quality improvement tools; specifically, a failure mode & effect analysis (FMEA) of the selected practice problem and an Ishikawa (fishbone) cause and effect diagram to analyze, improve, or mitigate related risks. This assignment will allow for the application of the DNP Essential IV sub-competencies through sequential development of workflow steps in relation to a practice problem and promotion of presentation skills. Assignment content supports the professional formation, communication, and dissemination skills relevant to the DNP practice scholar.
This assignment has four components:
first, identify a practice problem stated in PICOT format;
second, conduct a failure mode & effect analysis of the practice problem;
third, develop an Ishikawa (fishbone) cause and effect diagram to analyze, improve, or mitigate related risks
and fourth, create a professional power point presentation with speaker notes for each slide to disseminate this information.
Course Outcomes
This assignment enables the student to meet the following course outcomes:
CO 4: Evaluate the types of healthcare information systems, knowledge-based systems, and patient care technology and the impact on patient safety, quality of care and outcomes measurement. (PO 7)
CO 5: Appraise consumer health information sources for accuracy, timeliness, and appropriateness. (PO7)
Total points possible: 250
Preparing the Assignment
Follow these guidelines when completing each component of the assignment. Contact your course faculty if you have questions.
Consider using the same practice problem identified in Week 4: Translation Science Project, including the practice problem, PICOT construction, and background/significance of the problem. Be sure to incorporate faculty feedback from the Week 4 assignment to maximize performance.
2) Review the examples of the Failure Mode and Effect Analysis (FMEA) and Ishikawa (fishbone) Diagram in Week 4, Explore page 2, Evidence-Based Practice: Improving Outcomes.
Use the
Use the and or or create your own fishbone diagram addressing the required five areas: (a) people, (b) environment, (c) materials, (d) methods, and (e) equipment to complete these components of the assignment.
Please submit to the assignment link the completed Week 6 Practice Problem Analysis PowerPoint Presentation with speaker notes for each slide integrating failure mode & effect analysis and fishbone diagrams into the powerpoint answering associated questions. Upload the finished powerpoint with speaker notes to assignment link.
3) Include the following components.
a) Introduction (1 slide)
i) Title of Practice Problem Analysis and Presentation
ii) Student Name
iii) Assignment Title
iv) Professor Name
b) Practice Problem Identification (1-3 slides)
i) State the Practice Problem in PICOT format (1 slide)
ii) Identify all PICOT components
iii) Describe the Background/Significance of the Practice Problem (1-2 slides) (cited)
iv) Identify inclusion criteria for the population
v) Identify exclusion criteria for the population
c) Failure Modes and Effects Analysis (1-2 slides) Identify three steps in the practice problem process with potential breakdown or process gaps
i) Identify at least one potential error that could occur at each of the three process steps (failure mode)
ii) Identify at least one possible cause of failure at each of the three process steps (failure cause)
iii) Identify at least one adverse consequence for each failure identified (failure effect) (see example in course Week 4)
iv) Using a scale of 1-10, rate the likelihood of occurrence of failure at each process step
v) Using a scale of 1-10, rate the likelihood of detection of failure at each process step
vi) Using a scale of 1-10, rate the likelihood of severity or harm if failure were to occur
vii) Calculate the risk profile number (multiply the score related to the likelihood of occurrence of failure x the score related to the likelihood of detection of failure x the likelihood of severity or harm if failure were to occur.
viii) Place completed FMEA form on powerpoint presentation and summarize analysis
d) Ishikawa (Fishbone) Cause and Effect Diagram (1 Slide)
i) Identify people involved in the practice problem
ii) Identify the environment in which the practice problem occurs
iii) Identify the materials used
iv) Identify the methods used
v) Identify equipment used
vi) Summarize cause and effect analysis
e) Conclusion (1 slide)
i) Summarize the purpose and findings of the analysis
ii) Provide and justify the main conclusions
iii) Draw inferences from the quality improvement analysis
f) References (1 slide)
i) Include in-text citations within the PowerPoint
ii) Provide complete matching references in APA format
iii) Includes a minimum of 4 scholarly sources
g) PowerPoint Presentation
i) Uses PowerPoint Template provided
ii) Uses Failure Modes & Effects Analysis Template Provided
iii) Uses Ishikawa Fishbone Cause & Effects Diagram Provided (Version A or B acceptable or create your own diagram addressing required areas)
iv) Presentation includes no more than 14 slides
v) Grammar and Mechanics are free of errors
h) Speaker Notes on PowerPoint Presentation: Create a professional power point presentation of the above components with speaker notes for each slide in which the Practice Problem Analysis is explained
i) Provide clear and easily readable slide presentation
ii) Capture all slide components and answers questions
iii) Present content with legible, comprehensive notes
